Panel PC Industrial Panel PC and Touch screen Panel PC provider
    FAQ
        

Q & A
Q: How to install Floppy Module on FlexPOS-120/150 ?
Q: How to install Modem Module on FlexPOS-120/150 ?
Q: How to install Wireless LAN Module on FlexPOS-120/150 ?
Q: How to apply Wake On Lan function on Heisei Motherboard PC661 & Flex600ST while using ATX power?
Q: How to programming the Flex600ST Watchdog timer?
Q: How to check and re-write LAN ID Code for PC661 & Flex600ST motherboard which are using SIS630 S/ST chip onboard ?

Q: How to check bios version & message on boot up screen?

Q: How to clear Bios CMOS and solve can not boot problem on Flex600ST motherboard ?
Q: How to re-write LAN ID Code for PC660 motherboard which are using RealTek RTL8139 chip onboard ?
Q: How to save current Bios to Floppy A:?
Q: How to set CPU-SDRAM Frequency under Bios for Flex600ST motherboard?
Q: How to solve touch function under Win98 for Poseidon, Lavenus-P and P-OPEN which are using PC660 mother board?.
Q: How to solve Windows 98 SE can not shut down problem ?
Q: How to update bios ?
Q: How to use touch function without keyboard and mouse under Windows O/S?

Q:    How to install Floppy Module on FlexPOS-120/150 ?

A:  Please click "fdd.zip" for downloading the install proceeding.


TOP

Q:    How to install Modem Module on FlexPOS-120/150 ?

A:  Please click "modem.zip" for downloading the install proceeding.


TOP

Q:    How to install Wireless LAN Module on FlexPOS-120/150 ?

A:  Please click "wireless.zip" for downloading the install proceeding.


TOP

Q:    How to apply Wake On Lan function on Heisei Motherboard PC661 & Flex600ST while using ATX power ?

A:  Please proceed the following steps for Wake On Lan application through your Local Network.

 Step 1 : Please make sure that your system is with ATX power supply . Power on the system and press "DEL" key to enter BIOS Setupà Power Management Setupà  PM Wake Up Events à press Enter àMACPME Power Up Controlà set to Enable àSave & Exit Setup à the system will reboot .


Ling Fluent https://www.vicodur.com/ro/ling-fluent/
învățarea limbilor străine rapidă
https://www.vicodur.com/ro/ling-fluent/


 

 

 

 

 Step 2 : After reboot, please enter Windows 98/2000/XP and select "shutdown" to let the system shutdown properly again. The system must be connected to your Local Network.

 Step 3 : Then, you can use Wake On Lan utility software to wake up the system through Lan Mac Address . This Wake On Lan function is just for local Network application only.

!@


TOP

Q:   How to programming the Flex600ST Watchdog timer?

A:

The Flex600ST   features a watchdog timer that can generate a system reset if the CPU processing comes to a halt.  This feature ensures the system dependability during unattended operation.  The watchdog timer is programmable.  In order to program the watchdog timer, a program writing I/O port address 444 (hex) needs to be written first.  The output data is a value of time interval. The value ranges from 01(hex) to 3F(hex), and the related time interval ranges from 0 to 63 seconds. 

After entering the data, the program has to refresh the watchdog timer by rewriting the I/O port 444 (hex) and setting it at the same time.  To disable the watchdog timer, the program should read I/O port 441 (hex).

Download the way to program the watchdog timer in BASIC


TOP

Q:   How to check and re-write LAN ID Code for PC661 & Flex600ST motherboard which are using SIS630 S/ST chip onboard ?
A: Utility files:
Diag.exe à For checking LAN ID Node
EE.exe à For re-write LAN ID Node
EE.dat à LAN ID Node file
Check LAN ID Node
Please boot up your system from DOS A: and excute Diag.exe file.

A:\> Diag 
Select "Adapter Information" to check Node ID of LAN Chip.
Re-write LAN ID Node
Step 1 :
Please check your LAN chip MAC address which is printed on PCB.
Open the file EE.dat and change MAC address for your PCB. 
For example:
If your MAC address on PCB is : 000199F01234 , then change ee.datAs below:
0001           ;Mac  address [2] [1]
F099           ;Mac  address [4] [3]

3412
           ;Mac  address [6] [5]            
ID Node
01 ,
00 ,
99 ,
F0 ,
12 ,
34
[1] ,
[2] ,
[3] ,
[4] ,
[5],
[6]
Step 2 :
After changed LAN ID into EE.dat file, then execute EE.exe file as

A:
\> EE  EE.dat

TOP

Q:  How to check bios version & message on boot up screen
A:  For example you are using Poseidon or P-OPEN or Lavenus which are Using PC660 motherboard.    
When you power on and boot up the system, you will see the following bios
Version and message on LCD Screen.
(69030ALL) 660, A2,A3 BX/ZX/69030 Standard BIOS 03/02/200

TOP


Q:  How to clear Bios CMOS and solve can not boot problem on Flex600 motherboard ?

A:  Please see the following picture, you will find Clear CMOS jumper JP5 near the lithium Battery.

Step 1 :
Please set JP5 jumper to Clear CMOS side for 2 or 3 seconds, then set it back as Default again which will clear Bios CMOS setting. 
Step 2 :
Connector CRT monitor and boot up again Flex600 motherboard
à Press "DE" key to enter Bios CMOS Setup Screen à Select "Load Optimized Defaults" à Press "Y"
Step 3 :
Select "Frequency/Voltage Control"
à "CPU Host/SDRAM/PCI Clock: Default à Press Enter to change à For example : if your CPU and SDRAM external frequency is 133Mhzà Then set it as 133/133/33  (Our PCI Clock is 33 Mhz) 
Step 4 :
After set CPU & SDRAM & PCI Clock
à Save & Exit à Reboot and check boot up screen, then you will see correct CPU type and frequency .

TOP


Q:   How to re-write LAN ID Code for PC660 motherboard which are using RealTek RTL8139 chip onboard ?
A: Utility files: Pg8139.exe  à For rewriting LAN ID Node                 8139.cfg, 8139a.cfg, 8139b.cfg, 8139c.cfg, 
Step 1.

Boot up your system from Dos6.22 A:  

Step 2.

Copy above files (Pg8139.exe, 8139.cfg, 8139a.cfg, 8139b.cfg, 8139c.cfg) To A:  

Step 3.

Execute Pg8139.exe under DOS A:
à Then it will show Successful message on screen.

TOP


Q:  How to save current Bios to Floppy A:
A:  Try to get one Bios file PC660ALL.bin from Hei-Sei Customer Service Dept. Utility file à Awdflash.exe 
Step 1.
Boot up the system from A: Dos6.22. Press F5 key during booting up to by
Bypass Autoexec.bat and Config.sys in order to make pure DOS mode. 
Step 2.

A:
\> Awdflash PC660ALL.bin
Press "Y" to save current bios, and give it a file name as you wish Give it a name (as you wish), then it will save and back up into your floppy. After saved, press "N" not to program PC660ALL.bin Bios into your system.

TOP

Q:  How to set CPU-SDRAM Frequency under Bios for Flex600ST motherboard
A:  Please follow below steps to set CPU-SDRAM Frequency under Bios in order to run correct CPU and SDRAM type & speed. If you don't set , our Default setting is only running at 100 Mhz frequency for CPU and SDRAM.  
Step 1 :
Boot up FLEX600 motherboard and press "
DEL" key to enter CMOS Bios Setup screen. 
Step 2 :
Select "Frequency/Voltage Control"
à "CPU Host/SDRAM/PCI Clock: Default à Press Enter to change à For example : if your CPU and SDRAM external frequency is 133Mhzà Then set it as 133/133/33  (Our PCI Clock is 33 Mhz) 
Step 3 :
After set CPU & SDRAM & PCI Clock
à Save & Exit Setupà Reboot and check boot up screen, then you will see correct CPU type and frequency.  
Importance Notice:
 
(1)   Do not set CPU Clock at Jumper JP1. Please set under BIOS Setup as above steps.
(2)   When you change CPU type & speed and found motherboard can not boot up, then you can Set Clear CMOS Jumper JP5 for 2 or 3 seconds, then set back again and test to boot up.
(Because your previous CPU frequency might be frequency 133 Mhz, and you change to use CPU with 100 Mhz frequency only. That is why, it will cause "Can not boot up problem")

TOP

Q:  How to solve touch function under Win98 for Poseidon, Lavenus-P and P-OPEN which are using PC660 mother board.
A: Please test by following below steps to solve Touch Screen function under Win98 
Step 1.

Please remove Sound & TouchScreen Driver under Win98.

Step 2.

Please delete Autoexec.bat, Config.sys and ESSOLO.* files under C:\
Step 3.
Please reboot and press
DEL key to enter CMOS BIOS Setup and make sure Serial Port 3 is set IRQ 5 under Integrated Peripheral Setup
Step 4.

Please save and exit CMOS BIOS Setup, reboot and enter Win98 to install       TouchScreen Driver at first.

Step 5.

Then install again Sound Driver at second. You can check and see Sound Driver is using IRQ10 and TouchScreen is using COM3 IRQ 5 under System Device Manager.

TOP


Q:  How to solve Windows 98 SE can not shut down problem ?
A:  Please execute Microsoft program file under Windows 98 at first. Then, it will show and stop at the screen message  

"It is safe to power off now"
 
Because all of our Poseidon, P-OPEN and Lavenus systems are using AT power supply. So, you have to switch off power button to power off the system.

TOP

Q:  How to update bios ?
A:  For example :  to update Bios file PC660ALL.bin Utility file à Awdflash.exe 
Step 1.
Boot up the system from A: Dos6.22. Press F5 key during booting up to by Bypass Autoexec.bat and Config.sys in order to make pure DOS mode. 

Step 2.
 
A:
\> Awdflash PC660ALL.bin Press "N" not to save current bios, press "Y" to program  Press F1 key to reset and reboot the system.. 

Step 3.
 
During reboot, press "
DEL" key to enter BIOS CMOS Setup Screen. Select "Load Setup Default" or "Optimal Bios Default", press "Y" Select "Save & Exit" à Reboot the system.

TOP


Q: How to use touch function without keyboard and mouse under Windows O/S
A: Please follow below steps to remove mouse and keybord and make touch screen function work properly.                                         
Step 1.

Please disconnect mouse and just connect Keyboard on your system. 

Step 2.

Enter Windows O/S, then it will show "PS/2 mouse is not detected".  

Step 3.

Please use keyboard and click icon of "Never shows this message again".  

Step 4.

Reboot Windows O/S, and remove keyboard from system